A note about amplifiers
It is possible, just wire a normal input jack to your subwoofer and hook it up to your guitar amp. How do you hook up a sub-woofer and amp? Hook all the negatives together, and hook all the positives together. If you are working on a car stereo system you can simply disconnect the battery terminals.
As far as sealed vs ported, check out this article for help deciding. The only way to wire that gear together is like this. Good to know from a expert and I believe the amps do have on board fuses. Running it parallel to two channels is safe for the amp and sub.
How to Wire a 4 Ohm Amp to a 2 Ohm Speaker
You can achieve the same results with series-parallel wiring like this. Unfortunately, check dating we're only licensed to sell gear in the United States and Canada. What is the difference between a dual voice coil sub and a single voice coil sub? My question is can it be possible to over power the Type R?
Wire it like this diagram. Currently I have the subs wired to just one of the two terminal cups on the box and I was wondering if there is any reason that I should wire each sub to its own terminal cup. You bridge the amp not the sub.
What way should it be wired for max impedance. How do you insall a amplifier? To do this you should add together the speaker impedance number for all of your speakers. The sentence you quote out of context is about system efficiency and matching an amp to a sub.
Any suggestions on which amp I should purchase. Thank you for the help I greatly appriciate it. Do I wire a sub to each set? What is the best way to wire this sub? How would I be able to figure out the ohms of the subs?
Their toll-free number is on your invoice. Don't use car stereo components in home stereo equipment. Whether it will sound better, louder, softer, or worse - no one can say until you do it.
They should be alright as long as you set the amp's gain low enough to never allow distorted bass to play. Not sure why it is better than their regular ones. We will assume that the amplifier will deliver up to W per channel, so two speakers will be used on each channel. Is this amp able to power the sub enough or should I look for something more powerful? If the bass and sub-bass are quiet or not present at all, something is mis-wired.
Nic, Without knowing precisely what amp and subs you're referring to, we can't help you with advice. The cap should be located nearest the subwoofer amplifier, where it can do the most good restoring energy to the system when needed. Delmain, Having headroom is always good, for just the reasons you mention. Amps themselves don't have ohms, updating old iphone that's what subwoofers have. Hey Buck I have gone through the diagrams and understand the wiring for the most part.
You can find one at about any car audio store, I. Are the subs dual voice coil or single voice coil? The best you can do with that gear is to wire each voice coil separately to each output channel of the amp. Just make sure it has plenty of free space around it for cooling itself.
- Wiring multiple drivers parallel and also series can produce odd damping factors for amps to control effectively.
- No idea of internal wiring.
- The amp has two pairs of speaker output terminals that are wired together - just use one set.
- Also can I put two amp circuit breakers in to be safe?
If you no longer wish to receive the call, please click the button to cancel your request. Which wiring would be better? If you don't have a mic jack on your amp, your out of luck.
2 channel bridged amp driving a 2 ohm load Pro Help Needed
The best wiring diagram for dual core sub can be found in the accompanying link. This will be based upon the total impedance and the power output of your amplifier. If I need to call, dating for anime I will.
If so how should i wire it? The best way to choose components for a car audio system is to give Crutchfield a call and talk to one of our Advisors who'll make certain you get the right gear for yourself and your vehicle. You'll want to wire your gear together like this.
Nice amplifier by the way Zapco dump the Planet Audio junk Boss owns that company. Sounded real nice, but amp got hot. It sounds awesome I am just concerned about melting down something important.
And if so is that to much? My question is for rca's, do I need a separate set for each channel? More Print this page Share this page. An amplifier itself has no ohms - it senses whatever load is attached to its output, and responds accordingly.
- And I'd be more confident in any advice I give you if I knew the brand names and model numbers of your gear.
- Already answered Not a question Bad question Other.
- The amplifier provides the power.
No Diagram Available
If you want a question answered about a system, you must identify the gear by model numbers as well as brand names. You will need this wire to make the connections from your amplifier to your sub-woofers. My guess is I need an amp. Chris, Not knowing exactly what amplifier or subwoofers you have make it impossible to give advice on how to wire them together.
Wiring Subwoofers What s All This About Ohms
Car audio and home theater gear rarely play well together. If you want a question answered about a system, it's best you identify the equipment in question by brand names and model numbers. They should be able to accomplish this by either lowering the subwoofer output of the receiver, or lowering the sub amp's gain, or both. It is freaking incredible.
At the heart of every speaker and sub is a voice coil. However, this rockford fosgate site does Is this accurate? Get real help from an expert like Trevor Contact us.
Ben, There are two ways to wire your gear together. How to bridge the amp is usually indicated at the amp's speaker wire terminals. Bridging refers to adjacent channels of an amplifier that can work together to produce more power than just one channel.
For example if you have two subs that each pull W, you would want an amp that produces a minimum of W. Will this amp push these subs adequately in your opinion? Any other brands that I looked up got moderate praise. You could add a fan to cool things down, if you want. Let's hope the amp hasn't suffered any damage.